Adirondack Town Of Franklin
Adirondack Town Of Franklin

EXCAVATOR PUBLIC NOTICE

September 30, 2015

Thank you for your interest in the Town of Franklin's sealed bid solicitation for the purchase of an 18,000lb-20,000lb Excavator. The Town of Franklin wishes to trade in a 1999 John Deere Excavator with the trade-in value subtracted from the purchase of the new machine.

Detailed information regarding the 1999 John Deere by contacting the Town of Franklin Highway Garage at 518.891.1578. Questions regarding this bid should be directed to Highway Superintendent Jacques DeMars at 518.524.3111

Sealed bids must be received by Wednesday, October 14, 2015 at 2pm. Faxed or emailed bids will not be accepted. Sealed bids should be addressed to:

Lauren LeFebvre, Town Clerk
PO Box 209
Vermontville, NY 12989

Sealed bids can be dropped off at the Town Clerk's Office located at 7 Cold Brook Road in Vermontville M-Th 9am-2pm.

The Town of Franklin desired specifications can be found below. The Town will accept bids that are comparable to the specifications in this bid packet.

Sincerely,
Lauren LeFebvre
Town Clerk


EXCAVATOR INFORMATION
ENGINE
TypeLiquid cooled, 4 cylinder, diesel
Engine hp (Gross)66.6 / 2000 rpm
Bore X Stroke3.70 X 4.72 mm
Displacement203.3 cu. in.
Fuel Consumption (75% load)2.7 gph
Air CleanerDual Element
LubricationForced lubrication
Cooling SystemPressurized Radiator
Charging Output80 Amp
Capacities:
Fuel Reservoir30.4 gal
Cooing System2.8 gal
Engine Oil2.6 gal
Hydraulic Reservoir19.8 gal
Wheel Motor0.36 gal
Drive System:
Traveling Speed1.7/3.1 mph
Maximum Traction Force14,616 lbs.
Length of Track on the Ground 90.6"
Under Carriage Shoe Width17.7"
Ground Contact Pressure5.22 psi
Hydraulics:
System TypeOpen / Closed Center, load sensing
Pump Type / QuantityPiston / 2. Gear /1
Totai Pump Output55.6 gpm
Auxiliary Flow (SP1/SP2) 26.4 /17.6 gpm
Bucket Digging Force 14,660 lbf
Arm Digging Force8,554 lbf
Dimensions:
Overall Length (Transport)253.9"
Overall Height100.0"
Overall Width86.6"
Clearance Under Upper Structure28.7"
Tail Swing Radius57.8"
Rear Swing Clearance14.2"
Standard Blade
Blade Width X Height86.8" x 19.7"
Maximum Lift Above Ground19.7"
Maximum Drop Below Ground 19.7"
Hydraulic Angle Blade
Blade Width X Height86.6" x 20.1"
Maximum Lift Above Ground22.8"
Maximum Drop Below Ground25.2"
Maximum Swing Angle25° Left or Right
Swing System:
Unit Swing Speed9.5 rpm
Boom Swing Angie70° left / 60° right
Operating Weight:
Cab, rubber tracks, standard blade . 18,280 lbs.
Cab rubber tracks, angle blade19,140 lbs.
Working Range
Maximum Digging Depth15' 1.1"
Maximum Reach @ Ground Legal 23' 6.3"
8' Flat Bottom13' 11.7"
Maximum Vertical Digging Depth12 7.6"
Maximum Digging Height23' 11.4"
Maximum Dumping Heignt17' 2.7'
Climbing Ability36% / 20°
Lift Capacity:
Over End Blade Grounded
4 Ft. Load Point Height
12 Ft. Load Radius6,500 (lbs.)
KEY SPECIFICATIONS
Air Conditioned Cab
Type of tracksRubber / Steel
Operating weightStandard blade models: 18,280 / 18,390 lbs.
Angle blade models: 19,140 / 19,250 lbs.
Maximum digging depth15’ 1.1"
Output (SAE J1995 gross)66 hp @ 2000 rpm
Rear Swing Clearance14.2"
OPERATING AREA
Digging controlsTwo pilot operated, console mounted joystick levers control simultaneous boom, arm bucket, and house swing.
Operating patternTwo pattern selector valve for selecting ISO or SAE control pattern without tools or leaving seat.
Blade controlsBlade up, down, and float control by a separate right-hand lever Hydraulic dezer blade angle functions controlled by rocker switch on same lever. Lever houses two-speed travel switch in the forefinger location
Track controlsStraight travel when operating other circuits, Two self-centering hand and foot levers control speed and direction Travel speed selector switch or blade lever
Boom swing controlsRight foot pedal controls boom swing.
Auxiliary hydraulic controlsSP1 version: SP1 right-hand pilot control mounted. Bi-directional, proportional, self-centering thumb switch. Forefinger on/off trigger operates hold switch. SP1 & SP2 version: SP1 left-hand and SP2 right-hand pilot control mounted Bi-directional, proportional, self-centering thumb switch. Forefinger on / off trigger operates hold switch. Variable maximum oil flow control rate for SP1 and SP2 adjustable from operator's seat through electronic control panel.
Intelligent control panelAdvanced features provide Information that eases operation and maintenance, integrates controllers with easy to read backlit digital meters, includes visible and audible alarms, scheduled maintenance reminders, refueling assistant, advanced diagnostics
Engine controlsKey operated preheat, start and stop. Required preheat period is automatically controlled according to the engine coolant temperate. Engine speed controlled by separate console mounted dial.
Auto-ldling SystemAutomatically returns engine to idle after 4 seconds of inactivity. Engine speed returns to control setting with movement of any control. On / Off switch console mounted.
Suspension seatHigh back, cloth seat with headrest and retractable seatbelt. Adjustments for seatback angle fore/aft, weight compensation, seat height.
ENGINE
TypeFour cylinder, liquid-cooled, overhead valve, direct injected, E-CDIS diesel
Output (SAE J1995 gross)66.6 hp @ 2000 rpm
Output (SAE JI349 net)62.3 hp @ 2000 rpm
Displacement203.3 cu in.
Fuel consumption, 75% full load rated speed2.7 gph
Sound level @ ear cab model77 dB(A)
"F" shaped fan blades cabin models (low noise)Standard equipment
Under hood mufflerStandard equipment
Dual element cyclone type air cleaner w/ dust cupStandard equipment
Fuel / water separatorStandard equipment
Self-bleed fuel systemStandard equipment
Starter motor12 volt, gear reduction type, 3.6 hp
Variable speed cooling fan (fuel conservation)Standard equipment
DIGGING PERFORMANCE
Arm breakout force8,554 lbf
Bucket breakout force14,660 lbf
Maximum digging depth15' 1.1"
Maximum digging height23' 11.4"
Maximum dumping height17' 2.7"
Maximum reach @ ground level23' 6.3"
Maximum vertical digging depth12' 7.6"
HYDRAULIC SYSTEM
AccumulatorStandard equipment
Adjustable auxiliary hydraulics maximum oil flowStandard equipment
Auxiliary hydraulics flow26.4 gpm SP1, 17.6 gpm SP2
Auxiliary relief setting2,988 psi
Auxiliary valves and piping routed to armStandard equipment
Control ValveMaximum 13 spools, parallel type, open/closed center
Cushioned arm, boom, swing and travel circuitsStandard equipment
Direct to tank return line SP1Standard equipment
Hydraulic oil coolerStandard equipment
Hydraulic pumps2 ea. Variable type, 1 ea. Gear type
O-Ring sealed high pressure fittingsStandard equipment
Pressure regulated hydraulic tankStandard equipment
Main relief valve setting3,974 psi
Simultaneous boom, arm, bucket, travel and house swing operationStandard equipment
Swivel negative brakeStandard equipment
Swivel reverse preventionStandard equipment
Total flow capacity55.6 gpm
Travel negative brakeStandard equipment
CYLINDER SPEED
Angle bladeLeft. 2.1 seconds, Right: 2 3 seconds
ArmCrowd: 3.4 seconds, cushioned, Dump 3.2 seconds, cushioned
BladeUp: 2.3 seconds, Down: 3.0 seconds
BoomRa se. 3.1 seconds, cushioned, Lower 3.4 seconds
Boom swingLeft: 7.5 seconds, Right: 7.7 seconds
BucketCrowd: 3.1 seconds, Dump 2.2 seconds
DRIVE SYSTEM
Track typeSteel or 1/2 pilch rubber
Two speed travel with Auto DownshiftStandard equipment
Traveling speed1.7 mph Low/3.1 mph High
Drive motor typeTwo speed axial piston with automatic hydraulic brake. 156.7 cu in. per revolution low speed; 64.4 cu in. per revolution high speed
Type of reductionTwo stage planetary final drives with automatic disc brake
Travel negative brakeStandard equipment. Automatic engagement.
Maximum traction force14,615 lbs
Under carnage shoe width17.7"
Ground contact pressureRubber / Steel
Standard blade models5.22 psi / 5.25 psi
Angle blade models5.47 psi / 5.49 psi
Length of track on ground90 6"
Gradabilty36% / 20° Climbing angle, 27% / 15° Crossing angle
Rubber & steel track interchangeabilityStandard feature
Grease adjusted track tensionerStandard equipment
Upper track roller1 roller standard equipment each side
Numoer of lower track rollers5 rollers each side
30° angle and "X" shaped track frameStandard equipment
Travel negative brakeStandard equipment
SWING SYSTEM
Unit swing speed9.5 rpm
Swing motor typePiston motor and reduction gears. Automatic hydraulic cushioned brake, 55.5cu in / rev
Ring gear typeSingle row shear type ball bearings. Internal gear built into swivel bearing. Remote lubrication point.
Boom swing angle70° left / 60° right
Swivel negative brakeStandard equipment
Swvei reverse preventionStandard equipment
STANDARD BLADE
Blade width X height88.8" x 19.7"
Maximum lift above ground19,7"
Maximum drop below ground19.7"
HYDRAULIC ANGLE BLADE
Blade width X height86.6" x 20.1"
Maximum lift above ground22.8"
Maximum drop below ground25.2"
Maximum swing angle25° left or right
DIMENSIONS
Overall length253.9"
Overall height100"
Overall width86.6"
Clearance under upper structure28.7"
Tail swing radius57.5"
Tail swing overhang14.2"
Ground clearance15.4’
COOLANT AND LUBRICANT CAPACITY
Fuel reservoir30.4 gal
Coolant2.8 gal
Engine oil2.8 gal.
Hydraulic reservoir19.8 gal.
Wheel motor0.36 gal
Filters Cyclonic air filter, dual element, inner and cuter elements
Engine oil, cartridge type. full flow
Fuel / water separator and fuel tank clean out port
Fuel filter, in-line and cartridge type
Hydraulic fliers, suction & return, spin on type
In-line pilot filter cartridge type
ELECTRICAL
Engine alternator12 VDC, 80 amp
Battery12 VOC, 92 AH, 799 CCA
Instrumentation Auxiliary hydraulic flow presets
Battery charging warning lamp
Clock and calendar
Coolant temperature indicator / warning
Eco Plus° System Lamp
Engine oil pressure warning temp
Fuel level gauge
Fuel low warning tamp
Hourmeter
Pre-heat control lamp
Tachometer
Travel speed indicator lamp
ATTACHMENTS
Buckets, Pin-on and quick attach (Unless otherwise noted) 18" / 6.8 cu. ft. trenching bucket
24" / 9.4 cu. ft. trenching bucket
30" /10.8 cu ft. trenching bucket
36" / 12.1 cu. ft. trenching bucket
48" /10.8 cu ft. grading bucket
54" /12.2 cu ft. grading bucket
54" / 9.6 cu. ft. QA tilt grading bucket
60" / 13.5 cu. ft. grading bucket
Bolt-on cutting edge for 48". 54". 60" grading buckets
Attachments, Pin-on and quick attach (Unless otherwise noted) 80" QA grading blade
36" & 48" excavating rake
24" frost ripper
18" compaction wheel
Hydraulic thumb
750 ft. lb. hydraulic breaker
1 000 ft. lb. hydraulic breaker
SAFETY EQUIPMENT
Automatic house parking brakeStandard equipment
Automatic travel parking brakeStandard equipment
Auxiliary hydraulics on / off switchStandard equipment
BeaconOptional. Prewired for easy installation
Engine start safety lockoutStandard equipment
Grab handles for entry & exitStandard equipment
HornStandard equipment
Joystick and travel control lockoutStandard equipment
Low travel speed reset @ engine startStandard equipment
Non-slip surfaces for entry & exitStandard equipment
Operator protective guards (OPG)Canopy end cab meet OSHA 1926.1003 / ISO 10262 1998 (Top Guard Level 1)
Retractable seat beltStandard equipment
Rollover Protective Structure (ROPS)Meets OSHA 1926-1001/ISO 3471 1994/SAE J1040 MAY94
Tip-Over Protection Structure (TOPS)Canopy and cab meet IS0 12117 1997
Travel motion armOptional
Work lights with guard1 boom mounted, 2 cab mounted, standard equipment
MANUALS

Operator's instruction Manual
Illustrated Pans List /
Work Shop (Maintenance)
WARRANTY
Basic warranty24 months / 2000 hours
Rubber track warranty12 months /1000 hours
DESIRED OPTIONS

Rubber Tracks
Hydrolic Power Angle Grading Bucket
Hydrolic Angle Dozer Blade with Float and Bolt-on Cutting Edge
Hydrolic Thumb
30” Digging Bucket
Quick Coupler
*DEALER MUST BE A FULL SERVICE DEALER AND HAVE ROAD SERVICE TRUCKS TO MAKE REPAIRS IN THE FIELD

Town of Franklin
P.O. Box 209, Route 3, Vermontville, NY 12989 · Tel: 518-891-2189 · Fax: 518-891-6389 · info@townoffranklin.com
© Town of Franklin · Website Design: Rainbow Graphics
You are the visitor. Thank You for stopping by.